Search results for "Long-period fiber grating"
showing 10 items of 42 documents
A Refractive Index Sensor Based on the Resonant Coupling to Cladding Modes in a Fiber Loop
2013
We report an easy-to-build, compact, and low-cost optical fiber refractive index sensor. It consists of a single fiber loop whose transmission spectra exhibit a series of notches produced by the resonant coupling between the fundamental mode and the cladding modes in a uniformly bent fiber. The wavelength of the notches, distributed in a wavelength span from 1,400 to 1,700 nm, can be tuned by adjusting the diameter of the fiber loop and are sensitive to refractive index changes of the external medium. Sensitivities of 170 and 800 nm per refractive index unit for water solutions and for the refractive index interval 1.40-1.442, respectively, are demonstrated. We estimate a long range resolut…
Sensitivity optimization with cladding-etched long period fiber gratings at the dispersion turning point
2016
This work presents a refractive index sensor based on a long period fiber grating (LPFG) made in a reduced cladding fiber whose low order cladding modes have the turning point at large wavelengths. The combination of these parameters results in an improved sensitivity of 8734 nm/refractive index unit (RIU) for the LP0,3 mode in the 1400-1650 wavelength range. This value is similar to that obtained with thin-film coated LPFGs, which permits to avoid the coating deposition step. The numerical simulations are in agreement with the experimental results. This work was supported in part by the Spanish Ministry of Education and Science-FEDER TEC2013-43679-R. J.L. Cruz also acknowledges financial s…
Measurement of UV-induced losses and thermal effects in photosensitive fibers using whispering gallery modes
2017
When a photosensitive (PS) fiber is exposed to UV-irradiation, a permanent refractive index change is induced in the core. As a result, according to Kramers-Kronig relations, the absorption coefficient (α) is also increased. This increment of the absorption can lead to a significant heating of the fiber when it is illuminated by a moderate optical power. Thermal effects may produce spectral changes in some fiber devices, as for example Long Period Gratings (LPGs) or Fiber Bragg Gratings (FBGs) [1].
Analysis of a microwave time delay line based on a perturbed uniform fiber Bragg grating operating at constant wavelength
2000
This paper presents the modeling of a new microwave time delay line based on a uniform fiber Bragg grating (FBG) with a section which period has been perturbed. The time delay can be modified by changing the position of the perturbation along the grating. Theoretical results are presented for a 5-cm long uniform grating and optical signal is modulated up to 18 GHz. Experimental setup used magnetic fields to change the period locally along the grating and a 330 ps maximum time delay is shown. Comparison between calculations and measurements show a perfect agreement. Such a delay line offers many advantages for beamforming applications in phased array antennas where the operation at a fixed w…
Automatic tunable and reconfigurable fiberoptic microwave filters based on a broadband optical source sliced by uniform fiber Bragg gratings.
2002
We demonstrate an automatic tunable transversal notch filter based on uniform fiber Bragg gratings and a broadband optical source. High tunability can be performed by stretching the fiber with the gratings written in series. Also, high sidelobe supression can be achieved by introducing tunable attenuators in a parallel configuration of the gratings.
Monitoring the Etching Process in LPFGs towards Development of Highly Sensitive Sensors
2017
Trabajo presentado en la Eurosensors 2017 Conference. París, 3–6 de septiembre de 2017. In this work, the monitoring of the etching process up to a diameter of 30 µm of two LPFG structures has been compared, one of them had initially 125 µm, whereas the second one had 80 µm. By tracking the wavelength shift of the resonance bands during the etching process it is possible to check the quality of etching process (the 80 µm fibre performs better than de 125 µm fibre), and to stop for a specific cladding mode coupling, which permits to obtain an improved sensitivity compared to the initial structure. This work was supported by the Spanish Agencia Estatal de Investigación (AEI) and Fondo Europeo…
Single- to three-wavelength switchable ytterbium-doped fiber laser based on intracavity induced loss by a long-period holey fiber grating
2011
In this paper, we propose and demonstrate a versatile and simple single-, dual- and three-wavelength switchable ytterbium-doped fiber laser using the intracavity induced-loss generated by a mechanically induced long-period grating (MLPFG) in a holey fiber. The laser net gain in the cavity is reshaped through the MLPFG by adjusting the twist rate and the pressure of the holey fiber in the long-period grating. In this way, the twist response of the MLPFG enables the laser to switch between the single-, dual-, and three-wavelength operations and the tuning of the simultaneous two- and three-wavelengths. These results are of great interest in the design of flexible multiwavelength sources with …
Dispersion induced effects of high-order optical sidebands in the performance of millimeter-wave fiber-optic links
2006
In this paper, chirped fiber Bragg gratings (CFBGs) are proposed as signal-phase controllers for microwave-photonic wireless downstream fiber links. The effect of high-order modulation optical sidebands that disturbs the output mm-wave signal due to the chromatic dispersion induced by the gratings is studied theoretically and experimentally. The 1st and 2nd mm-wave harmonics of the output signal have been measured for conventional intensity modulation and for intensity modulation with optical carrier suppression. In the last case, data transmission at 2.5 Gb/s is demonstrated through a chirped grating of 280 ps/nm dispersion in a 40-GHz modulated link.
Etched LPFGs in reflective configuration for sensitivity and attenuation band depth increase
2016
A reflection configuration setup for long-period fiber gratings is presented. It permits to obtain a unique band with attenuation double than that obtained in transmission configuration, which is interesting for applications where this value is reduced (e.g., the mode transition phenomenon). The method is based on the deposition of a silver mirror at the end of the optical fiber, which permits to absorb the power transmitted through cladding modes and to avoid the generation of interferometric bands. The method also solves the requirement of a precise cleave or to polish the end of the grating, a drawback present in other publications. The versatility of the setup has been proved by applica…
Measurement of the Electrostriction-Induced Refractive Index Modulation Using Long Period Fiber Gratings
2020
We report the measurement of the refractive index modulation in optical fibers generated by electrostrictively driven acoustic waves through the change in transmission in a long period fiber grating.